Free Shipping on all orders in the U.S.

OOber Tactical Fenix PD35 TAC Edition weapon light system accessories.

Fenix flashlights

OOber Tactical Fenix Weapon Light System Specs

Fenix PD35TAC Edition Flashlight


•Uses Cree XP-L HI V3 LED with a lifespan of 50,000 hours

•Powered by a single 18650 rechargeable Li-ion battery or two non-rechargeable CR123A batteries

•5 modes plus Strobe

oTurbo: 1000 Lumens (2 hr. 50 min. - 820 feet/250 meters)

oHigh: 350 Lumens (5 hrs. 10 min.)

oMed: 150 Lumens (12 hr. 25 min.)

oLow: 50 Lumens (29 hr. 30 min.)

oEco: 3 Lumens (430 hr.)

oStrobe: 1000 Lumens

•Boot-up battery level indication and low-voltage warning (works for 18650 Li-ion battery only)

•Digitally regulated output maintains constant brightness

•Reverse polarity protection, protects from improper battery insertion

•Anti-roll and anti-slip body design

•Tactical tail switch features instant activation

•Metal side switch for output selection

•Made of durable high-strength and oxidation-resistance 6061 aluminum

•Premium type HAIII hard-anodized anti-abrasive finish

•Toughened ultra-clear glass lens with an anti-reflective coating

•IP68 rated protection

oFearless of harsh environment

Totally protected against dust and foreign objects

Submersible to 2 meters for 30 minutes

•Over-heat protection

Batteries Used (NOT INCLUDED)

•Fenix PD35 battery compatibility: One rechargeable 18650 battery (accepts Fenix ARB-L18-2600, ARB-L18-2600U, ARB-L18-2900, ARB-L18-3500, or ARB-L18-3500U, and Tenergy).  Each has a different mAh.  The higher the mAh, the longer the runtime between charges.

•Fenix PD35 battery charger compatibility for all 18650 batteries:  ARE-X1, ARE-X1+, ARE-X2,  ARE-C1+, or ARE-C2+

•Two non-rechargeable CR123A batteries.  (Fenix does NOT recommend rechargeable CR123 batteries since they will not perform according to the specification chart included for the PD35 edition)

•Explanation for the batteries listed below as* "Caution":* These batteries can be used, but we highly recommend batteries with protective circuits. We recommend you use the batteries labeled "Recommended" or "Usable."

Size of Flashlight

•5.5 inches/139mm (Length) x 1 inch/25.4mm (Diameter)

•3.1oz/87-gram weight (excluding the battery)

What Comes With Your Light

•1 - Fenix PD35 V2.0 LED Flashlight with pocket clip

•1 - Fenix PD35 Holster

•1 - Fenix PD35 Lanyard

•1 - Spare O-Ring and Spare Rubber Boot

•1 - Fenix PD35 Instruction Manual

•1 - Fenix PD35 Warranty Card


•Uses Cree XP-L(V5) LED with a lifespan of 50,000 hours

•New Cree XP-L LED provides up to 251% performance boost from XP-G2 LED

•Modes of Operation


Turbo: 1000 Lumens (1 hr., 10 min.)

Low: 60 Lumens (29 hr., 15 min.)

Strobe: 1000 Lumens


Turbo: 1000 Lumens (1 hr., 10 min.)

High: 500 Lumens (2 hrs., 55 min.)

Mid: 200 Lumens (8 hr. 30 min.)

Low: 60 Lumens (29 hr., 15 min.)

Eco: 8 Lumens (140 hr.)

Strobe: 1000 Lumens

•Tactical tail switch with momentary-on function

•Rugged Stainless steel side switch

•Side switch only capable of mode changing under Outdoor Mode

•Advanced Digitally regulated output maintains constant brightness

•Low-voltage reminder indicates when battery replacement is needed

•Intelligent memory circuit, automatically enters last-used output mode when turned on

•Reverse polarity protection, to protect from improper battery installation

•Anti-roll, slip-resistant body design

•Made of durable aircraft-grade aluminum

•Premium Type III hard-anodized anti-abrasive finish

•Toughened ultra-clear glass lens with anti-reflective coating

•Waterproof to IPX-8 standard, underwater up to 6 1/2 feet for 30 minutes

Batteries Used (NOT INCLUDED)

•One rechargeable 18650 battery (accepts Fenix ARB-L18-2600, ARB-L18-2600U, ARB-L18-2900, ARB-L18-3500 (recommended), or ARB-L18-3500U, and Tenergy).  Each has a different mAh. The higher the mAh, the longer the runtime between charges.

•Compatible charges for all 18650 batteries:  ARE-X1 (recommended), ARE-X1+, ARE-X2, ARE-C1+, or ARE-C2+

•Two non-rechargeable CR123A batteries

Size of Flashlight

•5.4 inches/137mm  (Length) x 1 inch/25mm (Diameter)

•3.1 oz/89-gram weight (excluding the battery)

What Comes With Your PD35 TAC

•1 - Fenix PD35 TAC LED Flashlight with pocket clip

•1 - Fenix PD35 TAC Holster

•1 - Lanyard

•1 - Spare O-Rings

•1 - Spare Rubber Boot

•1 - Instruction Sheet and Warranty Card

Fenix ARB-L18-3500mAh Rechargeable 18650 Battery


•Fenix ARB-L18-3500mAh Rechargeable 18650 Battery

•Button Top Design

•Protection circuit built in the anode with a steel hat by riveting process

•Steel shell eliminates the risk of short circuit caused by collision and impact.

•Pressure Relief Vent: Expels waste gas generated by internal short circuit

•Expelling waste gas prevents a cell from inflating or exploding.

•Three Sets of Over-Heat Protection:  

oOver charge protection and over discharge protection

oShort circuit protection

oOverheating protection

•500 Charge Cycles: A properly maintained ARBL18 battery is designed to retain up to 75% of its original capacity at 500 full charge and discharge cycles.

Product Description

The next generation of 18650 batteries are here.  Introducing the top-of-the-line Fenix 18650 battery--an amazing 3500mAh rating. Fenix always continues to increase their focus and desire to keep safety as the highest priority and with this new ARB-L18-3500mAh 18650 battery, Fenix has built in features to prevent short circuits and designed multiple layers of protection within it. With the new button-top design, the new 18650 series better accommodates a variety of flashlight brands.

18650 batteries are perfect for powerful Fenix LED flashlights since they are rechargeable, have a long battery life, and can handle the power requirements of advanced LED flashlights.

ARE-X1 single-bay 18650 charger

Product Description

We are pleased to offer you the Fenix ARE-X1 single-bay 18650 charger, supported with micro USB charging.  The Fenix ARE-X1 smart charger is dedicated for 18650 and 26650 batteries.  It features Micro USB battery charging, USB battery discharging, and LED charging/discharging indicator.  There is a battery power detection indicator that informs you of power status easily so you never have to wonder the status of your battery.

Fenix AER-02 Remote Pressure Switch

Product Description

This is an exciting new release from Fenix.  The Fenix AER-02 Tactical Remote Pressure Switch.  This switch features momentary-on, constant-on and output selection (function may vary with flashlights). The Fenix AER-02 Remote Pressure Switch is dedicated for tactical flashlights.  The switch features a noiseless design with attached Velcro, which makes it convenient in your tactical missions or in hunting.  


•Works with the Fenix PD35, TK09, TK15, TK22, UC35, TK15C, and PD35TAC flashlights

•Noiseless pressure pad switch (30mm long) with a lifespan of 100,000 activations, features output selection (function may vary with flashlights) and longtime 1A electric current passing

•Tactical round switch features momentary-on/constant-on (function may vary with flashlights) illumination and longtime 3A electric current passing

•Velcro cushion for quick attaching

•Cable made from resilient PU material can be extended from 24cm to 80cm

•Tail adapter is made from T6-grade aluminum, type III hard-anodized anti-abrasive finish

•Waterproof to IPX-8 standard

•Tail adapter size:  1.0 inch (25.4mm) x 1.3 inch (31.5mm)

•Includes pad switch, coiled cable, and tail adapter

•Total weight:  2.3 oz. (65 grams)

Fenix ALG01 LED Flashlight Tactical Ring Mount


•Weight: 51 grams (excluding allen wrench)

•Length: 45mm

•Material: Flashlight Ring Aluminum, type 6063TS. Plastic SpacerPOM

•Hex Screw:  Steel, type 22

•Allen Wrench: Steel, type 45

•Precision Machined Aluminum with Anodized Black Matte Finish

•Mounting Base Designed with Locking Hex Screws to Fit on Picatinny/Weaver Rail

•Clever Adjustable Diameter Designed to Allow for Use with a Wide Range of Flashlights

•Universal Slide-on Flashlight Ring

With Plastic Spacer:  Fits Flashlight Diameter .93 inches to .95 inches (23.6 mm to 24.2 mm)

Without Plastic Spacer:  Fits Flashlight Diameter 1 inch to 1.02 inches (25.4 mm to 26.0 mm)

12GA Shotgun Mag Tube Tri Rail Picatinny Mounts 5 Position Shotgun Barrel Mount

design to fit onto most 1" diameter Extended Shotgun Mag tubes. 

When mounted onto you Shotgun Extended Magazine tube, this will allow you to attach multiple weaver & Picatinny style accessories to your shotgun. 

The rails are designed so that you can attach your accessories like Lasers and Flashlight at any of the 5 angles that the rails provide. 

You can either mount your accessories at the typical 3, 6, and 9 O’clock positions; or mount the accessories in the 4/5 and 7/8 O’clock positions. 

This can also be used on any 1" diameter accessories like 1" scope tube bodies, flashlights, and lasers. 

Mounts onto most 12 gauge shotgun mag tubes with the two provided Allen head bolts. 

Installation may require user to disassemble shotgun barrel, magazine tube/end cap/ clamp. 



Fits 1” Diameter tubes 

Material: Aluminum 

Color: Black 

Overall Height: 1.5” 

Overall Length: 1.4” 

Overall Width: 1.5” 

Weight: 1.3 ounce fenix flashlights